AC1200 WiFi Router Dual Band Wireless Internet Router, Speed Up to 1.2 Gbps, 4 x 1000 Mbps Gigabit Ethernet Ports, Bridge/Repeater Mode, Guest Network, IPV6, EasyMesh, Parental Controls
$26.99
Related Products
Product description
𝐀𝐂𝟏𝟐𝟎𝟎 𝐃𝐮𝐚𝐥-𝐛𝐚𝐧𝐝 𝐖𝐢-𝐅𝐢 𝐑𝐨𝐮𝐭𝐞𝐫: Dual-band wireless speeds up to 1200Mbps (300 Mbps on 2.4GHz + 867 Mbps on 5GHz). 2.4GHz band can handles some simple tasks like emails or web browsing while bandwidth intensive tasks such as gaming or 4K video streaming can be handled by the 5GHz band
𝐅𝐮𝐥𝐥 𝐆𝐢𝐠𝐚𝐛𝐢𝐭 𝐏𝐨𝐫𝐭𝐬: Gigabit Wireless Internet Router with 3 Gigabit LAN ports and 1 Gigabit WAN port, ideal for lots of internet plan and allow you to connect your wired devices directly, providing a more stable and reliable Internet experience
𝐒𝐭𝐫𝐨𝐧𝐠 𝐖𝐢𝐅𝐢 𝐒𝐢𝐠𝐧𝐚𝐥 𝐂𝐨𝐯𝐞𝐫𝐚𝐠𝐞: Equipped with 4 powerful 5dBi high gain antennas and Beamforming technology, this router delivers high speed internet throughout your home
𝐂𝐨𝐧𝐧𝐞𝐜𝐭 𝐌𝐨𝐫𝐞 𝐃𝐞𝐯𝐢𝐜𝐞𝐬 𝐒𝐢𝐦𝐮𝐥𝐭𝐚𝐧𝐞𝐨𝐮𝐬𝐥𝐲: MU-MIMO technology allows the router to communicate with multiple devices at the same time, which can reduce network congestion and lower latency
𝐓𝐡𝐫𝐞𝐞 𝐖𝐨𝐫𝐤𝐢𝐧𝐠 𝐌𝐨𝐝𝐞𝐬: Switch between Router, Bridge, and Repeater Modes to adapt to your network requirements
𝐒𝐞𝐜𝐮𝐫𝐞 𝐖𝐢-𝐅𝐢 𝐍𝐞𝐭𝐰𝐨𝐫𝐤: Encrypts WiFi passwords with WPA2-PSK to protect your network and connected devices from hackers, providing you with more comprehensive network security
𝐄𝐚𝐬𝐲 𝐒𝐞𝐭𝐮𝐩: Breeze through setup and manage your network with the intuitive web UI. You can also connect new devices to WiFi using the WPS button
𝐄𝐱𝐜𝐞𝐥𝐥𝐞𝐧𝐭 𝐂𝐨𝐦𝐩𝐚𝐭𝐢𝐛𝐢𝐥𝐢𝐭𝐲: Works with all Internet Service Providers, but in some cases a modem is required
𝐎𝐭𝐡𝐞𝐫 𝐌𝐚𝐢𝐧 𝐅𝐮𝐧𝐜𝐭𝐢𝐨𝐧𝐬: Parental control, guest Wi-Fi, IPTV, IPV6, Easymesh, etc.
8 reviews for AC1200 WiFi Router Dual Band Wireless Internet Router, Speed Up to 1.2 Gbps, 4 x 1000 Mbps Gigabit Ethernet Ports, Bridge/Repeater Mode, Guest Network, IPV6, EasyMesh, Parental Controls
Add a review
$26.99
G. X. –
Affordable and well made
This is the most affordable AC1200 Wi-Fi router with gigabit Ethernet port I could find on Amazon. Need such a router to be used as a network bridge to extend my Wi-Fi to the 2nd floor via a MoCA adapter. It works exceptionally well in terms of gigabytes Ethernet connection and Wi-Fi speed and signal stability.
Megan Breaden –
Easy to install
Works wonderful in my building. Would buy again if I ever needed to. I have 500 mbs internet and this worked great for that speed and was so affordable. Also was easy to install. I like that you can customize your password easily also.
Bambino –
Very good product!
Very good product!
Amazon Customer –
It did not work for me.
I was unable to log into the router to set it up using the username and password on the router. The instructions said to reset the device if this were the case. When I did so the router froze (LED continuously red) and I was unable to unfreeze it.
Old Jer –
Cost effective router
Inexpensive router works great. Very good range and super easy setup. Way better than I needed or expected for the price.
👉👈 –
not very fast, works without interruptions, not a large area, very good for the money
works well. it was a little difficult to set up, but following the instructions everything worked out. the internet is not the strongest, the range is quite short, but that’s enough. the price-quality is simply incredible. for its price this is the best
Kristopher –
An outstanding value. Works great, but a few caveats to note
It’s a great value and has been working beautifully since installation. There’s a few important notes depending on your use cases (individuals with vmware workstation installed on their PC, and individuals connecting this to a primary router to serve as an access point/bridge mode.)Important setup notes if you use VMware:By default, this device is assigned the static IP address 192.168.10.1. If you have VMware Workstation (or similar) installed, this can cause a conflict, VMware creates virtual network adapters that also use 192.168.10.1 by default. As a result, the router’s admin interface will not load, because your computer attempts to communicate with the VMware virtual NIC instead of the router.If you’re unable to access the admin interface, disable all VMware virtual network adapters on your PC. Once those are disabled, the router interface at 192.168.10.1 will load correctly. This issue had me convinced the HTTPS interface was broken until I identified the IP conflict during troubleshooting.Using this as a wireless access point:I’m using this unit as a wireless access point in my basement, connected to my main router upstairs via Ethernet. While it may seem logical to use Bridge mode for this setup, I recommend keeping it in Router mode. Bridge mode removes the ability to assign a static IP address, which makes management more difficult.Instead:1: Leave the device in Router mode2: Assign it a static IP address within the same subnet as your primary router3: Disable DHCP on this device (your main router should handle DHCP)4: Connect it to your main router using a LAN port, not the WAN portAfter doing this, all connected devices received proper IP addresses from my primary router and had full access to the internet and the rest of my network.
Denise:) –
Works very well!
We have starlink internet but I put this up for my printer and for anyone that comes over to have this password and no one have my starlink password. This works great! We have multiple people on it often and no issues no slow internet no issues range is great and setting up is a breeze!